SPACEKEEPER Workbench Casters kit 920 Lbs- Retractable Casters, 4 Pack

Very heavy duty casters that work well for woodworking shop equipment. Tie together with board and they both can be raised or lowered much easier. Roll easily.

When I got it, I ran a test by mounting it on a 2x4, it worked fine. Three weeks later after I built the 2'x4' woodbench, I installed all four legs. It works very well, solid and easy to operate it. But, two comments about this product: - The installation manual is a joke, useless in one piece of paper with simple drawing. Look their product pictures, that's more detail of how to do installation. -2nd, the template is1/8" off, too short, don't follow it. Use the real plate will get the job done right.

Fully supports my workbench. Easy to install with the provided template. My only criticism is that the supplied screws are prone to snap during installation. After the second one snapped, I switched to my own, higher strength screws. I would buy another set for my next mobile work project.

I put them on my three box rig. Put a piece of bar across them so I could raise one side at a time. Rolls good. Took it to the limit on weight capacity. Holding up well. I move my box frequently. Original wheels made it hard to access the top. Just right now.

Very well made, some of the normal casters don’t hold up very well these are a little more complex with the retractable function and I’ve got them installed on a 350 pound 4’-6” X 10’ woodworking table they roll perfect and turn excellent it can be pushed with one finger.

I tried to use the wheels to occasionally move around a tire machine. No problem with the installation. Used my own nuts and bolts, and drilled directly into the steel of the machine. Pushed the levers to raise each wheel, everything ok. Then I rotate the machine, everything ok, until I bumped the the side of a carpet runner on my concrete floor. PROBLEM. 3 of 4 wheel studs bent. POOR design, all the weight of a wheel is on the single hex part of the wheel stud. That might be 5/8"? Wheel metal must be made of very soft steel, Chinesium, probably. My wheels bent , yours might , too. That's when I found some used all steel wheels where the weight would be distributed over a much greater area, at least a 2" radius, each. So I spent about $40 to use the bracket/lever part, Junked the rest, and added my own wheels. Now , No problem. So Be aware that the poor design of the small stud area can't possible be rated for the 920 pound weight of a set of wheels. Unless you never bump into anything. If you're trying to move around something much lighter, it's probably fine. 920 pound rating , for the whole set, is B.S.

These wheels work great and are easy to install.

I managed to get these installed and working, no thanks to the bad instructions. The drawings don't represent the actual parts, so I installed the caster plate upside down. If I had gone back to Amazon and looked at the illustration, I would not have made this mistake, but who does that after you have ordered and received your product? The instructions have you completely assemble these before mounting them on the leg of your table. Do not do that. (photo #2) the caster and mechanism block easy access to the mounting screws. I made a block of wood and clamped it to the leg to set the height without tedious measuring while sitting on the floor. This worked great. On my first try, the caster had rotated inboard and the lever will NOT work if it does that. (photo #3) I thought the height was wrong, but determined that if the caster is rotated outward it work with the instructions mounting dimension. I did not have the issue of twisting the screw heads off, but agree with one reviewer's comment that the bolts could be a few mm longer. I also have not experienced broken bolts or bent mechanisms and one of my benches is extremely heavy. It appears that these will work and I don't expect to be moving this stuff around often so I think they are OK. I have installed two sets and am considering a couple more.

Me gusto el producto.

Already said - it’s the best thing since sliced bread. Allowed me to move my largest table and tuck it under my industrial shelving for ample work space. Glides like a new razor

Received and installed onto 4x4 legs, they're smooth so far! The workbench I have is probably around 350lbs with a vice and mitre saw on it. As other posters have mentioned the instructions aren't super clear but I did not think it was terribly difficult to figure out. In case anyone has any issues: Look at the product page pictures for which way they pieces should be oriented, the product photos in the images are pretty clear on which way things go together. There are 2 sizes of bolts provided, use the long one to attach the mettalic bottom plate that the caster attaches to and use the smaller of the 2 to attach the lever.

Herrajes 7 de 10 Llantas 10 de 10 Gomas 3 de 10 ( las tuve que pegar con silicona) Tornillos 3 de 10 (se nota que son de baja calidad) Pijas 1 de 10 (se barren al momento de instalar, utilice otras pijas de mejor calidad) En resumen, compren de otra marca.

Works perfectly. Heavy duty materials, can lift a lot of weight. However the instructions are somewhat contradictory and images unclear. First construct the bracket (silver piece should have ridges up), as in my photograph. Then cut a 2.4" high piece of wood and clamp it to the base of the leg. Install the bracket above that piece of wood. Only then attach the wheel to the bracket. Also, as others note, the orange/red step end falls off because the manufacturers used the wrong kind of glue (it has to attach plastic to metal). I re-glued with a two-part epoxy glue, then clamped it on for a couple of hours and now it's on solid.