POLYWOOD Presidential Rocking Chair in Black

These POLYWOOD chairs are fantastic. Price aside (which is high), these should outlast two or three pairs of wood or wicker chairs on my front porch. These two POLYWOOD composite chairs are replacing a fourteen year old set of woven wicker rockers that were getting discolored and began to unravel. This POLYWOOD material is a vinyl composite wood, like Trex decking and it withstands the elements fantastic. My front porch, despite the shady, late-afternoon photos I attached, gets pounded with direct sun and blowing wind; anything there takes a four-seasons beating. My prior furniture lasted only a few years before it began to break down; anything wood I've put there peels and chips in only about a year. This POLYWOOD set should last much longer and it has a 20-year warranty. As for the chairs, they were easy to assemble (the directions in UrbanLegend's review were great), they are also very substantial and heavy so they will not get blown around by the wind. Plus, their build quality will withstand them being sat upon by persons of size. The chairs themselves are very comfortable to sit in; both my wife and I (who vary in size by over a foot and 100+ pounds) can relax and rock nicely in them. The backs, if I had to point to a minor downside, are at an almost 90 degree angle. As such, you sit a bit erect. They are still quite comfortable though. They look great as well. I posted a few pictures of the two chairs on my stoop with the optional royal blue seat cushions along with a POLYWOOD end table.

I purchased two of these rockers for our front porch to replace wooden rockers that had faded and mildewed, and worse, we had one of the wooden rocker blades on our old chairs collapse under the weight of a rather robust friend. We decided to go with synthetic materials for durability and strength when we replaced the wooden chairs. I was not disappointed! These chairs are extremely well constructed, much heavier than the wooden ones we used to have. I read all the reviews and especially problems with assembly hardware, but went with them anyway. The hardware was fine and assembly was relatively simple, but the instructions are very sketchy. I will attempt to supplement them with what worked well for me. Please note this is not the same sequence as the instructions that come with it, however there is virtually no way it would go together if you took their instructions literally and read them in the sequence provided. In my opinion, the problems are not with the hardware but with the instructions. The screws are in fact made of aluminum which is soft and the screw heads can be stripped easily if not careful. However, aluminum won't rust like steel screws would do. The only other rustproof option would be stainless steel screws which are much more expensive. The aluminum screws work fine (and the heads are painted white to match the chair) as long as you follow these instructions. 1. Get out your cordless drill and make sure the battery is charged. It will save a lot of wrist twisting. 2. Sort the screws into four shorter screws and 12 long ones. You don't want to use any of them in the wrong places or you won't have enough of the correct size later. 3. Put the supplied hex-wrench bit in the drill. When using it, always stop when the screws are not all the way in - leave about 1/4" or more to hand-tighten with the supplied T-wrench. This will prevent stripping the screw heads out by torquing too hard with the drill bit. Also, make sure the drill bit is tight in the screw heads before you start the drill or you will strip the aluminum heads. 4. Attach the seat to one of the two side-frames, using two short screws. Use the drill bit but stop when there is still about 1/4" to go. 5. Attach the back frame to that side-frame, using long screws. Use the drill bit, stopping with 1/4" left to go. 6. Attach the other side frame to the seat and back frame. Use the two remaining short screws for the seat and long screws everywhere else. Again, use the drill but stop leaving about 1/4" to go. 7. Put the curved head bar in between the two side-frames. There are no screws, it squeezes into the two slots provided. 8. Attach the two straight braces between the legs. Long brace between the two front legs, short brace between the back legs. Use the drill bit but keep a grip on the braces with one hand as you activate the drill or they will just spin. Leave about 1/4" to go with the drill bit. 9. Using the supplied T-wrench, go back and hand-tighten all screws. Be careful to turn the leg braces so the widest side faces out. 10. Flipping the chair upside down, attach the rocker blades with the longest end facing the rear of the chair. Again, use the drill but leave about 1/4" and then hand-tighten the remaining 1/4" with the T-wrench. 11. Turn the chair right-side up, lay down your tools, sit in the chair and relax. Contemplate its comfortable curved seat bottom, nice wide arms, and sturdy seat back. As you rock back and forth, take a moment to savor the satisfaction of making a wise purchase decision, and assembling it yourself. Job well done! Of the two chairs I just assembled, everything fit perfectly on the first chair, but the second one took a little help from my wife to get the seat to fit into the slots provided - one of the slots was cut slightly askew in the side frame. I got it to go together with a little pushing and pulling, but if it hadn't quite fit I would have just shaved a little of the slot with a knife or drill to make it work - it wasn't more than about 1/16" off square with the frame. The chairs are very comfortable, quite heavy, extremely sturdy, have a 20-year warranty, and should last longer than my lifetime. I highly recommend these chairs and would buy more if I needed them.

A lot of plastic patio furniture has a modern or retro look, which is fine, but I really wanted a traditional porch rocker. We live in a place that gets over 60 inches of rain annually, so it needed to be durable, too. Wood is a recipe for heartbreak in this climate. Even synthetic wicker only lasted about 10 years on our covered porch. So I was very excited to find this chair! Perfect look, and a material that will definitely hold up to the elements! Assembly was easier than I expected - it's a lot of bolt-tightening, but everything fit, there were only 2 kinds of bolts, and the tool that was provided was probably the highest quality hex wrench I've ever gotten with a piece of furniture 😅 My only complaints, and they're small, are that I wish the seat were about 1 inch higher - I'm only 5'6", but I find the seat a little low. And the texture of the material, which I had expected to be smooth, looks nice but like it might catch a little more dirt/pollen/algae than a smooth finish. Time will tell, but it will also be very easy to clean since it's non-porous. And it looks a little more natural than a glossy smooth finish would, anyway. I like this enough that I think I'm going to replace the deck furniture at our cabin with the same stuff - worth the price for the quality and durability!

Esta muy bonita pero no trae los tornillos para armarla, por favor envien los tornillos

Great product, the quality is evident. Instructions are actually very clear and easy to follow and I installed alone. Yes it would be quicker with 2 people but also one person not a problem. Do not tighten all the screws while still lining up other pieces.. I used a powered driver to speed up screwing BUT make sure to then switch to the provided tool to hand tighten the screws for final torque as you do not want to over tighten and strip. My only complaint is that I ordered two chairs and the second has not arrived yet, hopefully today. Update, second chair arrived. The one side of the chair back did not have any pilot holes. Note the first chair had pilot holes on both sides of back piece while the second chair had pilot holes only on one side of the back rest and so made my own pilot holes with a drill. This worked like a charm and no issues putting together. There must have been an over sight at the fabrication plant.

I poured over reviews before buying this chair-I worried it would be too small, uncomfortable, hard to assemble, look like melted tires, not rock properly, etc. All things I read in reviews. You need a pillow for lumbar support if you’re sitting for awhile but really ok without too. It’s a good size, not some kiddie looking chair. I hired a handyman and he charged me $25 to assemble. He said it was a whole lot easier to assemble compared to an IKEA product, but it took him over a half hour snd he had an arsenal of tools handy. It is attractive-I think it looks like painted wood-I had it displayed in my living room to show friends before my husband got it for his 65th birthday snd they loved it! It doesn’t rock as smoothly as our vintage indoor wood rockers but still ok. Haven’t had a chance to rock outdoors due to our Ontario winter. So I am happy with my purchase-plan to buy another one and the table.

product was great

Perfect for outdoor comfort while watching our dog play